Select your location

Luminaires
Monitoring Interfaces CG-S for connecting luminaires to emergency systems
Serial Number Verified :
Authenticated:
The product is verified as being authentic; however, this does not guarantee the condition or fit for purpose of the product.

Monitoring Interfaces CG-S for connecting luminaires to emergency systems

Eaton monitoring modules enable general lighting systems from any manufacturer to be connected to central battery systems and thus integrated into the building emergency lighting concept. The modules are matched to the requirements of central battery systems installations making it possible to monitor and control up to 20 luminaires in only one circuit.

Using the ballasts, luminaires on one circuit can be operated in different switching modes such as maintained light, non-maintained light or switched maintained light.

Here in the case of the N-EVGs (electronic ballasts), the emergency lighting level of each lamp can be individually set for battery operation from 30 to 100 % of the nominal luminous flux. Addressing and adjustment of the luminous flux is performed, as usual, via easy to access coding switches. Please observe our electronic control gear requirements for monitoring third-party luminaires.

Monitoring Interfaces CG-S for connecting luminaires to emergency systems
Load 1.5 to 400 W
Universal monitoring modules
Ambient temperature
Enlarged range
STAR-Technology
Reduced installation costs

Features

  • Reduced battery capacity/costs due to settable luminous flux ratio
  • Low operating costs due to decreased standby losses
  • Shortened inspection effort due to CEWA GUARD technology: Automatic function monitoring of up to 20 luminaires per circuit
  • Reduced installation expenditure with STAR technology: Freely programmable mixed operation of the switching modes per luminaire in one circuit
  • Reduced installation expenditures as no additional data line to the luminaires is needed
  • Increased safety through SLI technology: Monitoring of up to 8 individual LEDs in series connection
  • Avoidance of installation failures due to mains connection being protected against polarity reversal
  • Minimised dimensions
  • Greater ambient temperature ranges
  • With ENEC symbol, certified by independent test centre

Increased safety through intelligent individual LED monitoring


The new SLI technology (Single LED monitoring Intelligence) enables a safe error message even if a single LED fails. Up to 8 LEDs in series connection can thus be individually monitored.

Combined with an automatic function test, this signals a reduced luminaire luminous flux emission due to a defective LED and necessary repair work can be initiated immediately by the operating personnel.

Maintaining building security by complying with the required lighting parameters for safety lighting is significantly improved by this procedure.

Das neue Gymnasium Bochum 06.12.2012©
enec-logo-black.jpg

ENEC - certified by an independent test centre

The ENEC symbol (European Norms Electrical Certification) is a European examination symbol created by CENELEC (European Committee for Electrical Standardisation) which confirms that the device on which this symbol is fixed to automatically complies with all requirements of the European testing laboratory.

All Eaton modules must be subjected to these stringent tests and are then allowed to display this symbol.

eaton-ceag-el-cps-v-cg-s-frontal-40071352409.jpg
V-CG-S 4-400W
eaton-ceag-el-cps-v-cg-sb_1-seitlich-40071352008.jpg
V-CG-SB.1
eaton-ceag-el-cps-v-cg-s2-seitlich-40071352410.jpg
V-CG-S2 1,5-30W
eaton-ceag-el-cps-v-cg-suw-seitlich-40071352443.jpg
V-CG-SUW
eaton-ceag-el-cps-v-cg-se-seitlich-40071352528.jpg
V-CG-SE 4-400W
eaton-ceag-el-cps-cg-k-seitlich-40071352529.jpg
CG-K 4-400W

Intelligent modules ensure greater safety

With Eaton monitoring modules, electronic ballasts or LED supply modules, luminaires for general lighting systems from any manufacturer can be connected to central battery systems and thus integrated into the building emergency lighting concept.

The modules matched to the requirements of central battery systems installations make it possible to monitor and control up to 20 luminaires in only one circuit.

Using the ballasts, luminaires on one circuit can be operated in different switching modes such as maintained light, non-maintained light or switched maintained light. Here in the case of the N-EVGs (electronic ballasts), the emergency lighting level of each lamp can be individually set for battery operation from 30 to 100 % of the nominal luminous flux.

Over 50 years of safe evacuation expertise

Eaton offers a wide range of emergency exit and safety luminaires. Featuring CEWA GUARD & STAR technology available as standard, they offer the basis for minimized inspection and maintenance costs. Innovative lighting technology combined with highly efficient LEDs ensure up to 70% less power consumption and significantly lower maintenance costs with a service life up to 50,000 hours.
How to buy from Eaton
Contact us

Phone +40 21 361 0909