Download document () of 20
Send email
Download
You have exceeded the download limit
Eaton XNE Analog input card XI/ON ECO, 24 V DC, 8AI(voltage, current)/4(PT, ni, R)
| Product Name |
Eaton XNE Accessory Input card
|
| Catalog Number |
140037
|
| EAN |
7640130095311
|
| Product Length/Depth |
161.5 mm
|
| Product Height |
74.5 mm
|
| Product Width |
13 mm
|
| Product Weight |
0.064 kg
|
| Certifications |
IEC/EN 61131-2
CE Rated data for terminations according to IEC/EN 60947-7-1 IEC/EN 61000-6-4 IEC/EN 6113-2 cULus IEC/EN 61000-6-2 |
| Electric connection type |
Plug-in connection
|
| Features |
Analog outputs configurable
Input, voltage Input, resistor Fieldbus connection over separate bus coupler possible Input signal, configurable Input, current Analog inputs configurable Input, resistance thermometer |
| Fitted with: |
Connectable nickel sensors: Ni100, Ni1000 (according to DIN 43760)
Connectable platinum sensors: Pt100, Pt500, Pt1000 (according to DIN IEC 751) |
| Functions |
Diagnosis function
|
| Current consumption |
30 mA, from module bus, Analog input modules
35 mA, from supply terminal |
| Degree of protection |
IP20
NEMA 1 |
| Limit frequency |
1.5 Hz (- 3 db)
|
| Mounting method |
Rail mounting possible
|
| Number of channels |
8 (U/I)
|
| Product category |
XNE Slice module
|
| Type |
XI/ON I/O module
|
| Voltage type |
DC
|
| Drop and topple |
According to IEC 60068-2-31, free fall according to IEC 60068-2-32
|
| Shock resistance |
Continuous according to IEC/EN 60068-2-29
Mechanical, According to IEC/EN 60068-2-27 |
| Vibration resistance |
According to IEC/EN 60068-2-6
|
| Ambient operating temperature - min |
0 °C
|
| Ambient operating temperature - max |
55 °C
|
| Ambient storage temperature - min |
-25 °C
|
| Ambient storage temperature - max |
85 °C
|
| Environmental conditions |
Harmful gasses - SO2: 10 ppm (relative humidity < 75%, no condensation)
Harmful gasses - H2S: 1 ppm (relative humidity < 75%, no condensation) |
| Relative humidity |
5 - 95 % (indoor, Level RH-2, non-condensing for storage at 45°C)
|
| Air discharge |
According to EN 61100-4-2
|
| Burst impulse |
According to IEC/EN 61000-4-4
|
| Contact discharge |
According to EN 61100-4-2
|
| Electromagnetic fields |
According to IEC EN 61100-4-2
|
| Emitted interference |
230 - 1000 MHz (radiated, high frequency, according to EN 55016-2-3)
30 - 230 MHz (radiated, high frequency, according to EN 55016-2-3) |
| Radiated RFI |
IEC/EN 61100-4-6
|
| Surge rating |
According to IEC/EN 61000-4-5 Level 4
|
| Voltage dips |
According to EN 61131-2 (Voltage fluctuations/voltage dips)
|
| Terminal capacity |
0.25 - 1.5 mm², flexible without ferrule, H07V-K
0.25 - 1.5 mm², solid, H07V-U 0.25 - 1.5 mm², with ferrules without plastic collar according to DIN 46228-1 (ferrules crimped gas-tight) 0.25 - 0.75 mm², with ferrules with plastic collar according to DIN 46228-1 (ferrules crimped gas-tight) |
| Gauge pin |
A1 (according to IEC/EN 60947-1)
|
| Stripping length (main cable) |
8 mm
|
| Rated operational voltage |
24 V DC (supply terminal)
|
| Supply voltage at AC, 50 Hz - min |
0 VAC
|
| Supply voltage at AC, 50 Hz - max |
0 VAC
|
| Supply voltage at DC - min |
20.4 VDC
|
| Supply voltage at DC - max |
28.8 VDC
|
| Connection |
Connection of sensor types Pt100, Pt200, Pt500, Pt1000 and Ni100, Ni1000, NI1000TK5000 in 2- or 3-wire circuit
|
| Connection type |
Push-In spring-cage terminals, Connection design in TOP direction
|
| Protocol |
Other bus systems
|
| Input |
8 Analog input U/I
4 Analog inputs PT/NI |
| Input current |
40 mA (Analog input)
0/4 - 20 mA (Analog input) |
| Input impedance |
< 62 kΩ
≥ 200 kΩ |
| Input voltage |
Max. 20 V DC
-10/0 - 10 V DC (Analog input modules) |
| Measured value representation |
12-bit full range, flush left
16-bit signed integer Standard/extended range/PA (NE43) |
| Measured variables |
Current
Temperature (PT, NI) Resistance Voltage |
| Number of inputs (analog) |
8
|
| Number of outputs (analog) |
0
|
| Timing cycle |
0.1 % Offset error
|
| Explosion safety category for dust |
None
|
| Explosion safety category for gas |
None
|
| Potential isolation |
Through optocoupler: yes
|
| Equipment heat dissipation, current-dependent Pvid |
1.5 W
|
| Heat dissipation capacity Pdiss |
0 W
|
| Heat dissipation per pole, current-dependent Pvid |
0 W
|
| Rated operational current for specified heat dissipation (In) |
0 A
|
| Static heat dissipation, non-current-dependent Pvs |
1.5 W
|
| 10.2.2 Corrosion resistance |
Meets the product standard's requirements.
|
| 10.2.3.1 Verification of thermal stability of enclosures |
Meets the product standard's requirements.
|
| 10.2.3.2 Verification of resistance of insulating materials to normal heat |
Meets the product standard's requirements.
|
| 10.2.3.3 Resist. of insul. mat. to abnormal heat/fire by internal elect. effects |
Meets the product standard's requirements.
|
| 10.2.4 Resistance to ultra-violet (UV) radiation |
Meets the product standard's requirements.
|
| 10.2.5 Lifting |
Does not apply, since the entire switchgear needs to be evaluated.
|
| 10.2.6 Mechanical impact |
Does not apply, since the entire switchgear needs to be evaluated.
|
| 10.2.7 Inscriptions |
Meets the product standard's requirements.
|
| 10.3 Degree of protection of assemblies |
Meets the product standard's requirements.
|
| 10.4 Clearances and creepage distances |
Meets the product standard's requirements.
|
| 10.5 Protection against electric shock |
Does not apply, since the entire switchgear needs to be evaluated.
|
| 10.6 Incorporation of switching devices and components |
Does not apply, since the entire switchgear needs to be evaluated.
|
| 10.7 Internal electrical circuits and connections |
Is the panel builder's responsibility.
|
| 10.8 Connections for external conductors |
Is the panel builder's responsibility.
|
| 10.9.2 Power-frequency electric strength |
Is the panel builder's responsibility.
|
| 10.9.3 Impulse withstand voltage |
Is the panel builder's responsibility.
|
| 10.9.4 Testing of enclosures made of insulating material |
Is the panel builder's responsibility.
|
| 10.10 Temperature rise |
The panel builder is responsible for the temperature rise calculation. Eaton will provide heat dissipation data for the devices.
|
| 10.11 Short-circuit rating |
Is the panel builder's responsibility.
|
| 10.12 Electromagnetic compatibility |
Is the panel builder's responsibility.
|
| 10.13 Mechanical function |
The device meets the requirements, provided the information in the instruction leaflet (IL) is observed.
|
Product specifications
